- 您现在的位置：买卖IC网 > Sheet目录840 > B32686S2473K563 (EPCOS Inc)FILM CAP 0.0470UF 10% 2000V MFP
B32686S
Snubber
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 20
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
B32778G0406K
CAP FILM 40UF 1.1KVDC RADIAL
B32798G8306K
CAP FILM 30UF 875VDC RADIAL
B32916A3685K
CAP FILM 6.8UF 760VDC RADIAL
B32924B2155K
CAP FILM 1.5UF 310VAC RADIAL
B32926C3106M
CAP FILM 10UF 310VAC RADIAL
B32928E3256K
CAP FILM 25UF 310VAC RADIAL
B32934A3474K
CAP FILM 0.47UF 305VAC RADIAL
B37872R5102M041
CAP ARRAY 4CH 1000PF 50V 1206
相关代理商/技术参数
B32686S2473K564
功能描述:薄膜电容器 0.047uF 2KV 10% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S474J561
功能描述:薄膜电容器 0.47uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S474J562
功能描述:薄膜电容器 0.47uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S474J563
功能描述:薄膜电容器 0.47uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S7224J563
功能描述:薄膜电容器 0.22uF 1250volts 10% ESR 6.0mOhms Term=T3 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S7224J564
功能描述:薄膜电容器 0.22uF 1250volts 10% ESR 6.0mOhms Term=T4 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S7224J565
功能描述:薄膜电容器 0.22uF 1250volts 10% ESR 6.0mOhms Term=T5 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32686S7224K501
制造商:TDK Epcos 功能描述: